Skip to the calculator
DIVELUX More free sauna tools

Sauna Materials Calculator

Measure the hot room and the boards you plan to buy. Get the count of paneling boards, bench slats, insulation and foil. Plain geometry, with your own allowance for cuts.

Units
Inside size of the hot room
Length
ft in
Width
ft in
Ceiling height
ft in

Openings are taken off the walls. A door 2 ft wide and 6 ft tall is 12 sq ft. Enter 0 to count the walls whole.

Paneling boards

Cover width is the face you still see once tongue-and-groove boards are locked together. Measure a real board; it is narrower than the size on the label. The extra for cuts is your call. The 10% here is only a starting example.

Benches
Bench 1
Length
ft in
Depth in
Bench 2
Length
ft in
Depth in
Bench 3
Length
ft in
Depth in

Enter each level as its own bench. For an L-shaped bench, enter each leg as a bench. Only the seat slats are counted, not the frame under them. Sizes here are examples; the sizes makers publish are in the table below.

Insulation and foil

Coverage is printed on the pack and on the roll. Leave these empty to get the area only.

Paneling for the walls and ceiling

Enter the room size

The calculator needs JavaScript. The arithmetic it uses is written out below.

Measure twice before you order. This counts area and whole boards for a plain rectangular room. It does not know your framing, trim, floor, door, heater guard or fasteners, and it cannot see how your cuts fall. Check the heater manual for the wall materials and clearances it requires.

How the list is worked out

Everything on this page is geometry. There are no rules of thumb in the arithmetic. Every board size and every allowance is a number you enter.

  1. Walls. Twice the length plus twice the width, times the ceiling height, less the door and window area you enter.
  2. Ceiling. Length times width.
  3. Paneling length. Area divided by the cover width of one board. A board with an 85 mm face needs 1000 ÷ 85 = 11.76 meters of board for each square meter. A board with a 3 in face needs 4 ft for each square foot.
  4. Paneling boards. That length, plus your extra for cuts, divided by the length of one board and rounded up.
  5. Bench slats. The page fits as many whole slats across the bench depth as it can, with your gap between them. Each slat runs the full length of the bench in one piece, so it counts how many whole slats one board gives and rounds the boards up for each bench.
  6. Insulation and foil. The same wall and ceiling area, plus your extra for overlaps and cuts. If you enter what one pack or roll covers, the count is rounded up.

Sizes the makers publish

The page does not choose bench sizes for you. These are the figures sauna makers print, for reference. They do not all agree, and the manual of the heater you buy has the final say on ceiling height and clearances.

Published guidance, not used in the arithmetic.
WhatFigurePublished by
Bench depthat least 60 cm (about 24 in)HUUM
Seat width for each personabout 60 cm (about 24 in)HUUM
Bench levels above the floor30, 60 and 105 cm (about 12, 24 and 41 in)HUUM
Top bench to ceiling110 to 130 cm (about 43 to 51 in)HUUM
Ceiling heightno higher than 7 ft (2100 mm)Harvia KG manual, U.S.
InsulationR11 fiberglass with foil back in walls and ceiling, foil facing into the roomHarvia KG manual, U.S.
Panelingkiln-dried, clear tongue-and-groove softwood, moisture not over 11%Harvia KG manual, U.S.
Board length for each unit of area85 mm cover width: 11.76 linear m per m², before wasteSwedish Wood

Sources

What this page does not know. Whether your boards run up and down or across, where the joints fall, how much you lose to knots and bad ends, sloped ceilings, alcoves, the wall behind the heater, bench frames and supports, backrests, trim and fasteners. None of the published sources above gives a waste percentage, so the page does not suggest one. Local building and electrical codes come first.

The code is open source under the MIT license, so you can read every line.