Sauna Heat-Up Time Estimator
Pick the heater and the time you want to step in. See the heat-up range that sauna makers publish and when to switch on. A range, not a promise: every sauna is different.
Heat-up time
Pick a heater
The estimator needs JavaScript. The published ranges it uses are written out below.
Time your own sauna once and trust that over any range. These are the makers' general figures, not a calculation for your room. Before you switch on or light the fire, check that nothing is on or near the heater, and follow the heater manual.
What the makers say
How the estimate is put together
This page does not calculate anything about your room. Nobody can work out a heat-up time from the room size alone: insulation, the weight of the stones, vents, firewood and the weather all change it, and the makers themselves only publish ranges. So the page is a lookup of those published ranges, plus a clock.
- The range is the lowest and the highest figure that the sources below give for that kind of heater, from a cold start in ordinary conditions.
- Slow conditions. If you tick cold weather, or the size check shows a heater below the makers' sizing rule, the estimate starts at the long end of the normal range. Where a maker publishes a cold-weather figure, that becomes the top: HUUM says a wood-fired sauna can take up to 3 hours below 10 °C. Where nobody publishes one, the top is left open: "60 minutes or more". Starting at the long end is our reading of "longer". It is not a published number.
- The clock. "Switch on by" is the time you want to step in minus the long end of the estimate.
- The size check compares heater power with room volume. HUUM sizes electric heaters at 1 kW for each calculated cubic meter. The looser shortcut many North American retailers quote is 1 kW for each 50 cubic feet. A heater below even that is small for the room, and Harvia says of a heater that is too small that "it may take too long to reach the desired temperature".
| Heater | Published heat-up time | Published by |
|---|---|---|
| Electric, with stones | 30 to 60 minutes | Finnleo |
| Electric, with stones | about an hour; at least 30 minutes | Harvia KG manual |
| Electric, with stones | around one hour | HUUM DROP manual |
| Electric, with stones | 30 to 45 minutes | LeisureCraft |
| Electric, with stones | 160 °F in about 30 minutes, 190 °F in under an hour | Redwood Outdoors |
| Electric, cold weather | longer than 60 minutes | Redwood Outdoors |
| Wood-burning | 45 to 75 minutes | LeisureCraft |
| Wood-burning, below 10 °C (50 °F) | up to 3 hours | HUUM |
| Infrared | warm in as few as 10 minutes; 30 to 45 minutes to the top of its range | Finnleo |
| Infrared | 45 to 60 minutes | Sunlighten |
| Always-ready electric, on standby | 5 to 15 minutes to 50–60 °C (122–140 °F) | Harvia Forte manual |
What makes it slower
- Cold weather. Finnleo lists outside temperature among the things heat-up time depends on. Redwood Outdoors says to preheat longer than 60 minutes in colder months. HUUM says a wood-fired sauna can take up to 3 hours below 10 °C.
- A heater too small for the room. Harvia: "it may take too long to reach the desired temperature, and the heating elements may wear out faster".
- Insulation and room size. HUUM's wood stove manual says heating time depends on "the thermal resistance of the wall materials, room size and power of the sauna stove".
- A lot of stones. Redwood Outdoors notes longer preheating "especially if you have a heater with 80-100lbs of rocks".
- Too much ventilation. HUUM's troubleshooting for a heater that warms up too slowly asks whether there is too much ventilation in the room.
- Damp or thick firewood. HUUM's troubleshooting for a wood-fired sauna that is not heating properly starts with damp or too thick firewood.
Hot air is not the whole story
Harvia's manual says the stones normally reach bathing temperature at the same time as the room. It also says that with a heater that is too big, the air heats quickly while the stones stay too cool, and water thrown on them runs through. If water hisses weakly or runs off the stones, give them more time.
Sources
- Finnleo, Frequently Asked Questions. "A traditional sauna generally takes between 30 - 60 minutes to fully heat up, depending on your heater, heater size, sauna room size, and outside temperature." For infrared: "it can be warm in as few as 10 minutes; plan on 30 – 45 minutes to reach the upper temperature range".
- Harvia KG series heater owner's manual (PDF, U.S. models, hosted by a retailer). "If the heater output is suitable for the sauna room, it will take about an hour for a properly insulated sauna to reach that temperature." Troubleshooting: "You must allow at least 30 minutes for sauna heat-up time."
- HUUM DROP user manual (PDF). "In a properly insulated sauna room and with a heater of the right capacity, it will take around one hour to reach the desired temperature."
- Harvia, FAQ about the energy consumption of sauna bathing. "Typically, the sauna is initially heated for about an hour, after which the stove is still on for another hour." Also the note on a heater that is too small for the room.
- LeisureCraft, Sauna Heater Buying Guide. Electric heaters "reach temperature in 30–45 minutes; wood-burning stoves need no power and take 45–75 minutes".
- Redwood Outdoors, Sauna Operation FAQ. "In general, for electric heaters the sauna will heat up to 160F in ~30 mins and to 190F in <1 hour." "In colder months, you may need to preheat your sauna longer than 60 minutes."
- HUUM support, Wood-burning sauna stoves. "When the temperature is below 10°C, heating the sauna can take up to 3 hours." Also the troubleshooting list for a sauna that is not heating properly.
- HUUM support, Electric sauna heaters. Troubleshooting, "Heater warms up too slowly".
- HUUM HIVE Wood installation and user instructions (PDF, hosted by a retailer). "Heating time of the steam room is dependent on the thermal resistance of the wall materials, room size and power of the sauna stove."
- Sunlighten, First timers guide to sitting in a sauna. "Allow 45–60 minutes for your sauna to warm up."
- Harvia Forte owner's manual (PDF, hosted by a retailer). Users "need not wait long as the sauna room can be quickly (5–15 minutes) heated to a pleasant bathing temperature (+50…+60 °C)", as long as standby heat is kept in the heater.
- HUUM, How to dimension a sauna heater. "One calculated cubic meter presumes one kilowatt of the heater's power." The first rule behind the size check.
- The Sauna Place, How many kilowatts do you need for a sauna heater? A retailer on the 1 kW per 50 cubic feet shortcut: it "lands at the top of" the makers' printed ranges and "leaves little or no margin".
What this page does not know. Your insulation, stone mass, vents, firewood, chimney draft, the temperature you bathe at, and the exact model you own. Only one maker in our sources prints a general figure for wood-burning stoves, so that range rests on less than the electric one. There is no published upper figure for a cold electric or infrared sauna, which is why the page says "or more". Massive heat-storing wood stoves and smoke saunas that are fired for hours are not covered.
The code is open source under the MIT license, so you can read every line.
More free sauna tools